aluminium-guide.com

The Aluminium Profiles Surface Defects Catalogue

Aluminium-Guide offers the new paid content called “The Aluminium Profiles Surface Defects Catalogue”.

This catalogue contains visual quality characteristics of extruded profiles made of soft and medium-strength aluminium alloys such as 6060, 6063, 6005A, 6061 and 6082. The visual quality characteristics of profiles made of high-strength aluminium alloys, such as alloys of the 2xxx, 5xxx and 7xxx series, may also have their own types due to its high alloying and peculiarities of their manufacturing technology [1, 2].

All presented surface defects are classified into three sections for reasons of their occurrence:

  • Extrusion-press-related surface defects
  • Metallurgical-related surface defects
  • Mechanically-related surface defects

The document is intended to facilitate coordination between customers and manufacturers of extruded aluminium profiles by providing agreed terminology, description and images that are understandable to both parties. It can also be useful in training new employees in the production and supply of extruded aluminium profiles.

Below are examples of defect descriptions and brief information on the content of sections 1, 2 and 3 of this catalogue of defects.

1 Extrusion-press-related surface defects

1.1 Pickups (pick-ups)

Small particles of aluminium and aluminium oxides that were torn from the surface of the aluminium profile and later settled on its surface again. They are in the form of a comma or comet, which are oriented in the direction of extrusion. May occurs in connection with the “die lines” defect [4].

Torn, comma-like spots on the surface of extruded products caused by a local material deposition on the surface of the die [5].

Picture 1 – Schematic view of the “pick-ups” defect [4]

Figure 2 – “Comet tail” appearance of the “pick-ups” defect [3]

Figure 3 – Model of the “pick-up” defect [7]

1.2 Die lines

Grooves running in the direction of extrusion, which often end at points where alumi-nium material particles adhere. May occurs in connection with “pick-ups” defect [4].

Continuous longitudinal line formed on an extruded product caused by minor irregularities and/or the build-up of aluminium or non-metallic inclusions on the bearing surfaces of the die [5].

Micro die lines. Even with an optimum die bearing length and extrusion temperature, together with highly polished die bearings, die lines are still observed to occur. These die lines are finer and shallower and are termed micro die lines [3].

Figure 4 – Schematic view of the “die lines” defect [4]

Figure 5 – Die lines and micro die lines [3]

Further this section 1 includes 13 more defect types and 20 more images.

2 Metallurgical-related surface defects

The section 2 includes 8 defect types and 14 images.

3 Mechanical-related surface defects

The section 3 includes 12 defect types and 20 images.

Full version of the catalogue

The full version of the catalogue includes 34 defect types and 59 images.

This catalogue gives you the ability to:

  • distinguish between the types of surface defects of aluminum profiles;
  • identify the causes of these defects;
  • take prompt action to prevent the occurrence of these defects.

References

  1. P. K. Saha, Aluminum Extrusion Technology – ASM International, 2000.
  2. Extrusion of Aluminium Alloys / T. Sheppard – Springer Science+Business Media Dordrecht, 1999
  3. Extrusion Defects Fundamentals & Solutions for Optimum Finish / J. Fourmann – Rio Tinto – 2017
  4. Merkmale von Aluminium-Strangpreβprofilen – IWK, Aachen, 2001
  5. GAG Guidance Document 001, Terms and Definition – 2011.
  6. Product defects in aluminum extrusion and their impact on operation cost / A.F.M Arif et al, KFUPM, Saudi Arabia, 2002.
  7. Surface quality of aluminium extrusion products / X. Ma, PhD Thesis – University of Twente, The Netherlands, 2011
  8. Defect Analysis in Anodizing / Barry R. Ellard – ET 2000 – 2000
  9. The Identification and Prevention of Defects on Anodizing Aluminium Parts / T. Short – Metal Finishing Information Service Ltd – 2003.
  10. Care of Aluminium – https://www.hulamin.com – 2021

The full version of “The Aluminium Profiles Surface Defects Catalogue” can be found by the link below.

Exit mobile version